Arduino Pro Mini ATmega328P 3V-5V, 16MHz

SKU: 4260474032853.
Category: .

Arduino Pro Mini ATmega328P 3V-5V, 16MHz

$ 4.98

In stock

RangeDiscount
3 - 910 %
10 - 99915 %

The Arduino Pro Mini can be powered with an FTDI or CH340G cable or breakout board connected to its six pin header, or with a regulated 3.3V to 5.5V supply on the Vcc pin. There is a voltage regulator on board so it can accept voltage up to 12VDC. If you’re supplying unregulated power to the board, be sure to connect to the “RAW” pin on not VCC.

The ATmega328 has 32 kB of flash memory for storing code (of which 0.5kB is used for the bootloader). It has 2 kB of SRAM and 1kBs of EEPROM (which can be read and written with the EEPROM library.

Each of the 14 digital pins on the Pro Mini can be used as an input or output, using pinMode, digitalWrite, and digitalRead functions. They operate at 3.3 to 5V. Each pin can provide or receive a maximum of 40 mA and has an internal pull-up resistor (disconnected by default) of 20-50 kOhms. In addition, some pins have specialized functions:

• Serial: 0 (RX) and 1 (TX). Used to receive (RX) and transmit (TX) TTL serial data. These pins are connected to the TX-0 and RX-1 pins of the six pin header.

• External Interrupts: 2 and 3. These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value. See the attachInterrupt function for details.

• PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite function.

• SPI: 10 (SS), 11 (MOSI), 12 (MISO), 13 (SCK). These pins support SPI communication, which, although provided by the underlying hardware, is not currently included in the Arduino language.

• LED: 13. There is a built-in LED connected to digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it’s off.

The Pro Mini has 8 analog inputs, each of which provide 10 bits of resolution (i.e. 1024 different values). Four of them are on the headers on the edge of the board; two (inputs 4 and 5) on holes in the interior of the board. The analog inputs measure from ground to VCC. Additionally, some pins have specialized functionality:

• I2C: A4 (SDA) and A5 (SCL). Support I2C (TWI) communication using the Wire library.

There is another pin on the board:

• Reset. Bring this line LOW to reset the microcontroller. Typically used to add a reset button to shields which block the one on the board.

The Arduino Pro Mini has a number of facilities for communicating with a computer, another Arduino, or other microcontrollers. The ATmega328 provides UART TTL serial communication, which is available on digital pins 0 (RX) and 1 (TX). The Arduino software includes a serial monitor which allows simple textual data to be sent to and from the Arduino board via a USB connection.

A SoftwareSerial library allows for serial communication on any of the Pro Mini’s digital pins.

The ATmega328 also supports I2C (TWI) and SPI communication. The Arduino software includes a Wire library to simplify use of the I2C bus; see the reference for details. To use the SPI communication, please see the ATmega328 datasheet.

The Arduino Pro Mini can be programmed with the Arduino software download. For details, see the reference and tutorials.

The ATmega328 on the Arduino Pro Mini comes preburned with a bootloader that allows you to upload new code to it without the use of an external hardware programmer. It communicates using the original STK500 protocol reference , C header files.

You can also bypass the bootloader and program the ATmega328 with an external programmer.

The dimensions of the Pro Mini PCB are approximately 33 x 18mm.

(*) To operate the ATmega328P with 16MHz requires a supply voltage of at least 4.5V to be within manufacturers specifications. Tests in the temperature range of -20 to +85 degrees Celsius on almost 100 different ATmega328P development boards never showed any misbehavior. We use many of these chips in 3.3V applications, running 16MHz. We clearly say: You can run these boards on 3.3V or 5V, without any difference or occurring unreliability! If you run the ATmega328P on 3.3V, make sure you have a stable power supply, and a strong buffer capacitor as close as possible to the module. The brownout detection is factory set to 2.7V, and any voltage on the supply pins lower than that will trigger the reset (fuse setting can be re-programmed).

The on-board voltage regulator is a 5V type. To operate this board with 3.3V, you will need an 3.3V external power supply.

Microcontroller: ATmega328P
Board Power Supply: 3.35 -12 V
Circuit Operating Voltage: 3.3V – 5V
Digital I/O Pins: 14
PWM Pins: 6
UART: 1
SPI: 1
I2C: 1
Analog Input Pins: 6
External Interrupts: 2
DC Current per I/O Pin: 40 mA
Flash Memory: 32KB of which 2 KB used by bootloader
SRAM: 2 KB
EEPROM: 1 KB
Clock Speed: 16 MHz

Weight0.010 kg
EAN

4260474032853

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.